IAP-420 / IAP-420+

  • Description
  • Reviews (0)

Description

Specifications
IAP-420 IAP-420+
Physical Ports
10/100Base-T(X) Ports in RJ45 Auto MDI/MDIX                                                                                     2
P.O.E. PD port Present at ETH1
Fully compliant with IEEE 802.3af  Power Device specifi cation
Over load & short circuit protection
Isolation Voltage : 1000 VDC min.
Isolation Resistance : 108 ohms min
WLAN interface
Operating Mode AP/Bridge/AP-Client
Antenna Connector 1 x External reverse SMA-type antenna connector
Radio Frequency Type DSSS, OFDM
Modulation IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g/n: OFDM with BPSK, QPSK, 16QAM, 64QAM
Frequency Band America/FCC: 2.412~2.462 GHz (11 channels)
Europe CE/ETSI: 2.412~2.472 Ghz (13 channels)
Transmission Rate 802.11b: 1/2/5.5/11 Mbps
802.11g: 6/9/12/18/24/36/48/54 Mbps
802.11n(40MHz): UP to 150 Mbps
Transmit Power 802.11b: 13.5dBm ±1.5dBm
802.11g: 13.5dBm ±1.5dBm
802.11n(2.4G@20MHz): 13.5dBm ±1.5dBm
802.11n(2.4G@40MHz): 13.5dBm ±1.5dBm
Receiver Sensitivity 802.11b: -90dBm ±2dBm@1Mbps
802.11g: -72dBm ±2dBm@54Mbps
802.11n(2.4G@40MHz,MCS7): -68dBm ±2dBm
Encryption Security WEP: (64-bit, 128-bit key supported)
WPA/WPA2:802.11i (WEP and AES encryption)
WPA-PSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security SSID broadcast disable and enable
Protocol Support
Protocol ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, 802.1X, SNMP, STP
LED Indicators
Power Indicator LED x 3, PWR 1, 2, (PoE):
Green On: Power is on and functioning Normally.
100/1000TX RJ45 Port Indicator LED x 2 , Green for port Link/Act at 100Mbps.
WLAN LEDs WLAN Link /ACT: Green: Link,
Power
Redundant Input Power Dual DC inputs.  12~48VDC on 4-pin terminal block
Power Consumption (Typ.) 4watts
Overload Current Protection Present
Reverse Polarity Protection Present
Physical Characteristic
Enclosure IP-30
Dimension (W x D x H) 41(W) x 81(D) x 95(H) mm (1.6 x 3.1 x 3.7 inch.)
Weight (g) 292 297
Environmental
Storage Temperature -40 to 85°C (-40 to 185°F)
Operating Temperature -10 to 60oC (14 to 140oF)
Operating Humidity 5% to 95% Non-condensing
Regulatory approvals
EMI FCC Part 15, CISPR (EN55022) class A
EMS EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),EN61000-4-8, EN61000-4-11
Shock IEC60068-2-27
Free Fall IEC60068-2-31
Vibration IEC60068-2-6
Safety EN60950-1
Warranty 3 years

Reviews

There are no reviews yet.


Be the first to review “IAP-420 / IAP-420+”